Wireless Security System -Central Monitoring ( WT-200F / WR-200, WR-300 )

1. Emergency Feature

1. In case of a robbery or an emergency
happened to the elderly or

1. patients, transmits an emergency
signal to the wireless receiver

1. by pressing the emergency button.

2. Wireless Motion Sensor

1. Transmits a radio wave to the wireless
receiver or activates wireless

1. emergency lamp when it detects
an intruder or a fire.

3. Fire Sensor

1. Transmits a radio wave to the wireless
receiver or activates wireless

1. emergency lamp when it detects
smoke.

ㆍ Press “Armed” button on the remote control for more than 2 seconds,
then beep sound will be

ㆍ heard twice and the red light will blink
on the front of the transmitter for about 32 seconds. After

ㆍ that, it will send a signal to receiver to
notify the emergency when intrusion or a fire is detected.



※ Caution : The wireless transmitter will not be activated if
you are on the front of it

ㆍ while blinking. So please be away from the
detection range.



ㆍ To deactivate the system, press “OFF” button on the remote control
for more than one second

ㆍ when you come back. A beep sound will be
heard and it will be deactivated. Under deactivated

ㆍ status, the red light blinks for 2~5 seconds
when someone is detected.

ㆍ It transmits a signal to wireless receiver after 16 seconds when intrusion
is detected or after

ㆍ 2 seconds when a fire is detected. It transmits
radio wave with the type of alarm (Intrusion / Fire /

ㆍ Emergency / Accident / Gas leakage), sensed
location and time to the wireless receiver

ㆍ (WR-200, WR-300) and it stands by for 30
seconds for next event.



※ Please be sure to deactivate the transmitter within the entry
delay time of 2 or 16

ㆍ seconds to prevent undesired notification
to the receiver.



※ Wireless transmitter can be used with the intruder alarm and other
wireless sensors

ㆍ that Menix provides. The transmission distance
between the wireless transmitter

ㆍ and each wireless sensor is about 100 meters
at free space.

ㆍ Turn the power switch to ON after connecting power adaptor. The wireless
receiver sounds an

ㆍ alarm for thirty seconds by activating emergency
lamp and the detected time, transmitter’s location

ㆍ and the type of emergency will be displayed
on the LCD.

ㆍ Check the received messages using (▲) or (▼) button. After checking
the messages, press

ㆍ “SAVE” button, then emergency lamp and
LCD will be off and it goes to the initial display.

ㆍ (A : Intrusion, B : Fire, C : Emergency,
D : Accident, GAS)



※ Initial display will be automatically shown on the LCD after
30 seconds even if

※ “SAVE” button is not pressed after checking
the messages.



※ It stores Max 70 received data and you can check the event happened
before.



※ Master Remote Control

※ All the transmitters can be activated
or deactivated with a master remote control. In case of

※ emergency, you can send a signal to the
receiver through a close transmitter by pressing the

※ “Emergency” button.

※ The code of master remote control has to
be registered into all the transmitters for use.

Place the wireless transmitter on the chosen location where an intrusion can be detected easily but the transmitter doesn’t attract attention and install it as shown above. Enter the code of remote control into the wireless transmitter by pressing “ARMED” button within 8 seconds after turning the power switch to ON. A beep sound will be heard twice, which means the code of remote control has been entered into the transmitter. ※ Please keep the transmitter’s location and remote control code (the last 4 digits of remote ※ control S/N) in file as pair for each transmitter in order to enter them into wireless receiver.

Turn the power switch to ON with a ballpoint pen or other sharp-pointed tool after placing it in the security office where a security personnel stands by and connecting power adaptor. Each button on the wireless receiver is used for the setting of date, time, the code of remote control and transmitter location. Wireless Receiver Setup 1.Time Setup 2. Press “SET” button for more than 5 seconds, then a beep sound will be heard and LCD 2. displays time setup mode and you can set the date and time. 2. Wireless Transmitter’s code entry to Wireless Receiver 4. ㆍAutomatic Code Entry : Move to #001 and press any button on the Cybereye remote control 5. ㆍ towards to the receiver. With a beep sound, “####” will change to the same as last 4 digits 5. ㆍ of serial number on the back of remote control. Now the transmitter’s code has been 5. ㆍ entered into the receiver and press “SAVE” button to go to next address. 5. ㆍManual Code Entry : Enter the transmitter code manually using ◀▶ ▼▲ buttons

Turn the power switch to ON with a ballpoint pen or other sharp-pointed tool after placing it in the security office where a security personnel stands by and connecting power adaptor. Each button on the wireless receiver is used for the setting of date, time, the code of remote control and transmitter location. WR-300 shows you the sensed location using not only LCD but also LED panel for a immediate help. ㆍIn case of emergency, each section LED blinks and the siren make an alarm at the same time ㆍStop the siren by pressing the “Check” button on the receiver ㆍIt stores Max 70 received data and you can check the event happened before. ㆍMax 55 wireless transmitters per one wireless receiver ※ The receiver size or the LED quantity can be customized according to client’s request.

Major
Features

ㆍReceives data
ㆍfrom max 254
ㆍtransmitters
ㆍDisplays the
ㆍtype of alarm,
ㆍsensed
ㆍlocation
ㆍand time on
ㆍthe LCD

ㆍLocation LED
ㆍand siren
ㆍalarm
ㆍDisplays the
ㆍtype of alarm,
ㆍsensed
ㆍlocation
ㆍand time on
ㆍthe LCD
ㆍCompatible
ㆍwith
ㆍmax 55
ㆍtransmitters

ㆍDetects &
ㆍtransmits
ㆍintrusion, fire,
ㆍemergency
ㆍsignal to
ㆍreceiver
ㆍwith radio
ㆍwave
ㆍRemote control

ㆍTransmits
ㆍemergency
ㆍsignal to
ㆍreceiver
ㆍwith radio
ㆍwave
ㆍRemote control

ㆍExtends
ㆍtransmission
ㆍdistance
ㆍbetween
ㆍtransmitters
ㆍand receiver
ㆍ(Within 1km at
ㆍfree space)

Range

1Km (Depends on the obstacles)

Size

204 X 96 X 60mm

705 X 450 X 55mm

74 X 80 X 56mm

112 X 65 X 20mm

Weight

330g

5.6kg

94g

80g

Power

AC Adaptor ( DC 12V/500mA) / Rechargeable Battery (Option)

Wireless Motion Sensor (BS-200F)
It activates the wireless transmitter with radio wave when it detects an intruder’s
movement or high temperature (fire).

Wireless Door Sensor (DS-200F)
It activates the wireless transmitter with radio wave when it detects an intruder
entering through a door or window.

Wireless Siren (SR-200F)
It sounds a loud alarm when it receives a signal from a remote control or other
optional sensors.

Wireless Emergency Switch (ES-200F)
It activates the wireless transmitter with radio wave when the emergency button
is pressed.

Wireless Smoke Sensor (SS-200F)
It activates the wireless transmitter with radio wave when it detects smoke (fire).

Wireless Smoke Sensor (SS-300F)
It activates the wireless transmitter with radio wave and it sounds an alarm itself
when it detects smoke (fire).

Wireless Gas Sensor (GS-200F)
It activates the wireless transmitter with radio wave when it detects gas leakage.

Wireless Window Sensor (WD-200F)
It activates the wireless transmitter with radio wave when it detects a window
breakage or impact.

Wireless Wrist Transmitter (WS-200F)
It activates the wireless transmitter with radio wave when the emergency button
is pressed.

Wireless Pendant Transmitter (PR-200F)
It activates the wireless transmitter with radio wave when the emergency button
is pressed.

Wireless Outdoor Sensor (OS-200F)
It activates the wireless transmitter with radio wave when it detects an intruder’s
movement outdoors.

Wireless Emergency Lamp (LP-200F)
It blinks and sounds an alarm when it receives a signal from the optional
sensors or the emergency button is pressed.

Wireless Emergency Lamp (LP-300F)
It blinks and sounds an alarm when it receives a signal from the optional
sensors or the emergency button is pressed.